Novamid® ID 1030 (PA6/66)

Mit Novamid® ID 1030 Material für Fused Filament Fabrication (FFF),
Sie können Teile herstellen, die von denen, die mit Standardspritzguss hergestellt werden, kaum zu unterscheiden sind.

Dieses Open-Source-Filamentmaterial ist ein reines Polyamid 6/66 und wurde ursprünglich entwickelt
Vor vielen Jahren von unseren Experten für technische Kunststoffe für anspruchsvolle Spezialanwendungen häufig
rauer Umgebung und hohen Temperaturen (bis zu 125 ° C) ausgesetzt. Einfach an 3D-Druck angepasst,
Novamid® ID1030-Filamente bieten eine einzigartige Kombination von Eigenschaften, einschließlich herausragender Steifheit
und Duktilität für eine Reihe von Anwendungen - vom Transport über Sport bis hin zur Elektronik.

Ihr optimiertes Kristallisationsprofil verbessert die Schmelze und ermöglicht Teile mit ausgezeichneter Zwischenschichtfestigkeit und hoher Oberflächenqualität.

Novamid® ID1030 eignet sich gut für dauerhafte Anwendungen, die gute mechanische Eigenschaften erfordern.





Mögliche Anwendungen

Elektronik - Tischmontagevorrichtungen, kundenspezifische teilespezifische Lagerung

Transport

Sport & Lifestyle



Allgemeine Druckrichtlinien *

*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.

*) First layer : 100 - 150% of first layer thickness.

*) Novamid® can be used with a range of nozzle temperature (220–245 °C / 428–473°F). Preferred temperature to print your object is 230°C / 446°F. To generate a homogeneous melt, the melt temperature should always be above 225°C / 437°F. Optimal mechanical properties will be achieved at melt temperature between (225-245 °C / 437°F–473°F).

*)  Print speed: 50 - 100 mm/s (obeying the maximal throughput in cm3/s of the extruder). Print speed for "normal" nozzle size (0.4mm) and layer height (0.2mm), for other values print speed should be adjusted accordingly!

*)  Do only remove printed object from print bed when print bed has cooled down to ambient temperatures, as otherwise printed part can deform severely.

*)  Retraction dependent on printer type and filament diameter.

Filament length

Storage and conditioning

Novamid® ID1030 grades are supplied in airtight, moisture-proof packaging at a moisture level <0.05 w%.

In order to prevent moisture pick up and contamination, supplied packaging should be kept closed and undamaged. For the same reason, partially used bags should be sealed before re-storage. Allow the material that has been stored elsewhere to adapt to the temperature in the processing room while keeping the bag closed. To prevent moisture condensing on filaments, bring cold filaments up to ambient temperature in the print shop while keeping the packaging closed.

In case the filament has become wet, it should be dried. Using a hot air oven at 80°C for at least 4h is recommended. When storing the filament after printing, it is advised to seal the bag and add silica gel to the bag to keep the filament as dry as possible.

DSM Plastics Finder

For more technical information and guidelines please visit DSM Plastics Finder.

Product export information

Compliance *

This filament is compliant to below listed directives and regulations.

• RoHS directive 2011/65/EC

• REACH directive 1907/2006/EC

*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.