Pegasus PP-HGS25 Ultralight
Pegasus PP-HGS25 ist ein mit Hohlglas-Nanotechnologie veredeltes PP-Filament,
Dadurch ist dieses 3D-Drucker-Filament 20 % leichter und deutlich steifer als reine PP-Filamente.
Pegasus PP-HGS25 Ultralight ist das wahrscheinlich leichteste PP-Filament der Welt!
Pegasus PP-HGS25 ist ein PP-Filament, das mit Hohlglas-Nanotechnologie veredelt ist, was dies macht
3D-Drucker-Filament 20 % leichter als reine PP-Filamente. Die Modifikation mit 25% Mikrohohlglaskugeln
aus Natron-Kalk-Borosilikatglas machen Pegasus PP-HGS25 nicht nur zu einem extrem leichten Filament,
aber auch deutlich steifer als normales PP-Filament. Die inhärenten Eigenschaften der zugesetzten Mikrohohlglaskugeln
bieten eine Reihe einzigartiger Leistungsvorteile, wie Gewichtsreduzierung, Dimensionsstabilität, thermische
Isolation und eine niedrigere Dielektrizitätskonstante. Das macht Pegasus PP-HGS25 zu einem äußerst vielseitigen 3D-Drucker
Filament für verschiedene Anwendungen wie Automobil, Drohnen, schwimmende Anwendungen und Anwendungen, die erfordern
leichte, verschleißfeste und langlebige Teile.
Einzigartige Merkmale
-
extrem leicht
-
-
Gute Verschleiß-, Abrieb- und Ermüdungsbeständigkeit
-
Deutlich steifer als normales PP-Filament
-
hohe chemische Beständigkeit
-
nimmt keine Feuchtigkeit auf
-
Ausgezeichnete Zwischenschichthaftung
-
Ausgezeichnete Bauplattenhaftung mit EasyFix Adhesive - Nr. V (für PP-GF
General printing guidelines *
Nozzle size: ≥ 0.4mm |
Layer height: ≥ 0.1mm |
Flow rate: ± 104% |
Print temp: ± 215 - 245° C |
Print speed: Low |
Retraction: Yes ± 5mm |
Heat bed: ± 0 - 100° C * |
Fan speed: 50-100% |
Experience level: Intermediate |
*) Above displayed settings are meant as guidance to find your optimal print settings.
hese ranges in settings should work for most printers, but please do feel free to experiment
outside these ranges if you think it is suitable for your printer. There are a lot of different type of
printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.
*) Large Pegasus PP Ultralight prints can be printed on an unheated 2mm or 3mm PP plate,
hich can be attached to the print bed. Smaller prints can be printed on standard PP packaging tape.
Filament length
ρ: 0.75 g/cc |
50 gr coil |
0.5 Kg spool |
|
|
|
Ø 1.75mm |
± 27.7m |
± 277m |
|
|
|
Ø 2.85mm |
± 10.5m |
± 105m |
|
|
|
Product export information
HS Code: 39169090 |
Description: Monofilament |
Country of origin: the Netherlands |
Compliance *
This filament is compliant to below listed directives and regulations.
*) This declaration of conformity to directives and regulations is prepared according to our present
standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.